Quality · 2026-11-16 · 6 min read

Closure torque and leak testing: qualifying a pack before it ships

A cap that opens at 12 in-lb in the lab can leak at 8 in-lb on a filling line. How to set an application torque, test the seal, and write the numbers into the purchase order.

Leak claims almost always resolve to one of three numbers: the application torque the filling line used, the removal torque the customer experienced, and the sealing surface the mould actually produced.

None of them are visible on a drawing. All three are testable in an afternoon.

Application torque versus removal torque

Application torque is what the capping head applies. Removal torque is what the user needs to open it. The gap between them is the seal.

Apply too little and the liner never compresses; apply too much and the cap or the neck can distort, which creates a leak path that did not exist before. For most cosmetic closures, application torque sits in a band set by the closure diameter, and the band should be written down, not left to the operator's feel.

A torque tester costs less than a single recall. Measuring ten caps at start-up and ten at the end of the run is enough to prove the capping head is stable.

Three leak tests, three different failures

A vacuum test pulls air through a bad seal and shows bubbles in water. It finds liner defects and neck ovality.

An immersion test at pressure finds the opposite failure: product escaping. It is the test that matches a bottle lying in a bag on a shelf.

A compression test, where the filled pack is squeezed and held, finds seals that survive standing but fail when a customer grips the bottle. For squeezable packs this is the test that matters and the one most often skipped.

Run all three on the same sample set. A pack that passes one and fails another has a specific geometry problem, and the pattern tells you which.

What the mould contributes

The sealing surface is a moulded feature, and it wears. A neck with a damaged sealing land will leak regardless of torque, and the damage is often invisible until the pack is filled.

Ask for the sealing land diameter and flatness on the drawing, and check the first shots of every tool. On multi-cavity tools, check every cavity, not just the first: cavity-to-cavity variation is a classic source of intermittent leaks.

Accelerated ageing is not optional for a two-year claim

A pack that holds for a week proves very little. If the product claims a 24-month shelf life, the closure has to hold against creep in the liner and stress relaxation in the plastic.

A standard approach is elevated temperature storage, for example four weeks at 40°C, followed by the same torque and leak tests. It is a proxy, not a guarantee, but it catches the failures that appear in month nine.

Writing it into the purchase order

The qualification is only worth what is written down. Specify:

  1. Application torque range, and the method used to measure it.
  2. Removal torque range after ageing.
  3. Leak test method and pass criteria.
  4. Sample size and the accept number.
  5. Retained samples per lot, kept for the shelf life of the product.

When those five are in the order, a leak claim becomes a measurement instead of an argument. That is the whole point of qualifying a pack: not to prove it will never fail, but to know exactly what it was tested to.

Clear airless pump: the seal sits between collar and body, so torque and neck finish are tested together
Clear airless pump: the seal sits between collar and body, so torque and neck finish are tested together

Specifying this for a real product? Send the drawing or a reference sample.

Get a Quote Browse Products

Keep reading

Packaging guides · 2026-10-23

How to choose the right material for your cosmetic packaging

PET, PETG, PE, PP and glass each solve a different problem. A practical comparison for brand owners and product developers specifying a pack for the first time.

7 min readRead
Tube packaging · 2026-10-21

Applicator tubes: roller, ceramic, sponge or nozzle?

The applicator decides how the product feels before the formula does. A practical comparison of the four heads we fit most often, and the formulas each one suits.

6 min readRead
Tube packaging · 2026-10-19

Dual-chamber tubes: when two formulas must stay apart

Two-in-one products need the ingredients to meet at the nozzle, not in the tube. How co-extruded dual chambers work, what ratios are possible, and what filling demands.

6 min readRead